Licensed Electrician Serving Orland Park, IL
Orland Park's mix of established subdivisions and newer construction near LaGrange Rd means electrical needs vary widely — some homes need a straightforward panel upgrade, others need full wiring for additions and remodels. EMT Electric also installs standby generators and new light fixtures throughout the village, with Peter on every job and the permit pulled through the village.
Contact
Generators, fixtures and code updates in Orland Park
Homes in Orland Park's established subdivisions tend to share the same weak points by era: panels that are now full, ceiling boxes never meant to hold a fan, and kitchens and baths without the GFCI and AFCI protection current code expects. Electrical codes have changed a lot since many of those houses went up. When you remodel, the new work has to meet today's code, and before we quote, we explain which upgrades are required and which are optional, so the inspection holds no surprises.
Generator installation is one of the most common requests here. A standby generator with an automatic transfer switch keeps the sump pump, furnace, refrigerator and selected circuits running through an outage, and a larger whole-house unit can carry nearly everything. We do the load calculation, set the transfer switch and make the electrical connection. Routine generator maintenance is handled by the manufacturer's dealers, not by us. In newer homes with plenty of capacity, the work is more often fixtures — pendants over an island, a foyer chandelier, exterior lights and ceiling fans.
Popular projects in Orland Park
The jobs we're called for most often here.
Standby generator installation
We install standby generators with automatic transfer switches in Orland Park homes, sized to cover either the essential circuits or the whole house, and we handle the permit and inspection with the village.
Fixture and recessed lighting installation
From recessed lights in a family room to pendants over a kitchen island and a heavy chandelier in a two-story foyer, we mount every fixture on a box rated for its weight.
Panel upgrades before an addition
Additions and newly finished spaces in Orland Park often outgrow the original panel. We upgrade to 200 amps or add a sub-panel, and we coordinate the service change with ComEd.
Services
From quick fixes to full remodel wiring — here’s what EMT Electric handles.
Troubleshooting
- Troubleshoot & repair partial power
- Identify shorts, overloads, & failures
Fans & Ventilation
- Ceiling fans
- Attic fans & bathroom exhaust fans
Switches & Outlets
- Dimmers, 3-way, 4-way, timers
- Receptacles / GFCI replacements
Dedicated Circuits
- Dryer, AC unit, furnace, baseboard heaters
- Washer, microwave, oven, etc.
- Dishwasher & disposal power
Outdoor & Low Voltage
- Security/pole/landscape lights
- Photocells, motion sensors
- Doorbells & cable
Permits and inspections in Orland Park
Electrical permits in Orland Park go through the village's building department, and the electrical contractor may need to be registered with the village before pulling one. Generator installs, panel upgrades, additions and remodel wiring are inspected before they are signed off. When an older room is remodeled, the new wiring has to meet the code edition the village has adopted, including AFCI and GFCI protection where required. EMT Electric pulls the permit and meets the inspector.
Orland Park electrical questions
What size generator does my Orland Park home need?
It depends on what you want running during an outage. Covering the furnace, sump pump, refrigerator, lights and a few outlets takes a much smaller unit than also running central air and an electric range. We go through your panel with you, add up the loads you choose and recommend a size, along with a transfer switch to match.
Do I have to bring my whole house up to code if I remodel?
Usually not the whole house. The new and altered work has to meet current code, which often means AFCI and GFCI protection, tamper-resistant outlets and enough circuits in the remodeled area. Untouched rooms generally stay as they are unless something is unsafe. We explain what the inspector will expect before we give you a quote.
Can a ceiling fan go where a light fixture is now?
Often, but the box has to be rated for a fan. Many light fixture boxes are not, and a fan hung from one can work loose over time. We swap in a fan-rated box or brace, and if you want the light and fan controlled separately, we can add a second switch.
Why Orland Park Homeowners Choose EMT Electric
Peter Podczerwinski owns EMT Electric and is on every Orland Park job, with no subcontractors. Since 2008 the shop has kept it simple: same-day callbacks, free and firm quotes, and the permit and inspection handled whenever the work requires them.
Request a Quote
Fill this out and we'll get back to you as soon as possible.
Nearby areas we serve
We work across the neighborhoods and towns around Orland Park, out of our base in Oak Lawn.